Видео

Great video. Any idea if the Z06 parts are any different from the base model?

I learned this the hard way, when my wipers went mad🫣 after some heavy rain. Yet to find out the actual fault.☹️

It’s too bad GM put morons in charge of engineering for the C5. If C5 owners haven’t had to replace their primary fuel pump they are in for a shock when they do. I will not recommend a C5 to anyone due to the many stupid designs on the C5 such as the Torque tube , fuel tanks , Oil pressure sensor location, cheap Harmonic balancer , electronics under the battery and others. I bought a C5 with 7600 miles on it in 2012 and before I put 400 miles on it on a trip the fuel pump quit. We were 250 miles from home so it was towed to a local dealer. 2000 dollars later it was fixed. Surprise ,surprise !!

Great video! Looking to put these in our C5 Z. I'm 5'8" - would you recommend he A4's shaved? Car is being tracked frequently so helmet is on a lot of the time. I have the stock seat somewhat raised as it is.

What's sad is now the calipers are almost 500+ a piece as of June 2024. Crazy how much they have skyrocketed in price.

I wouldn't have even mentioned those scumbags who sent you on a wild goose chase you should have gotten their address and just kept parking the vette across the street and drive away every time the noticed you. 😂 😅

Hello, can anyone tell me what that wire is for? It's at 6:45 in the bottom of the large storage compartment. I've been trying to find out, but I have no idea. I thought it should be plugged into something, but I couldn't find anything.

Does my 86 c4 have opti spark? Great video 💯

GR8 vídeo clip Sir . Thanks for the advice: Bleed the inside caliper piston first then the out side.

Alguien que me pase un link para comprar un tanque con sensor solo encuentro sin sensor

Why not use vinyl paint

I like to see you replace the single light module

Well explained, just what I needed :)

i've pumped air with a bicycle pump through the feed hose at the fuel tank and got very little fuel leaking from the filter.

Is there any special way to remove the pulse regulator? Or does it just pull apart? Cheers!

with those short plugs the spark begins inside the cavity and should mean slightly longer flame propagation so it would need slightly more advance. Mechanically it puts twice as much stress on the aluminum threads and these engines are also pretty high in torque. there is also less heat dissipation through the treads but I don’t think it’s a problem

Hello. Tried to send an email to Twinflags performance but the email did not go through. Want to order a cover for the steering wheel. Do you have any suggestions what I can do? mvh Ruben, Norway, Z06

How can people allow a piece of automotive history like that to deteriorate like that? Pathetic. I know it won't be like that too long.

The big scary header mod

I bet you could slip an open end wrench onto the hex and spin it like that

What year is that red vet? Is that a ZR1

Remember there usually is left over fluid hiding in places in a trans, so the max fill is usually just the first one and less for replacing fluid

Reinstalling the pan with gasket, I found that by putting one bolt in on each side, that the other holes all automatically lined up easily for me as i placed it into the position. and loosely screw them in as you go just a rotation or two as you add all the bolts, making sure not to pinch or snag any part of the gasket. then make sure gasket is sitting nice all around as you snug it up before torqueing. My Range Rover had 23 bolts, its a GMC trans so same style over all

You just taught me how to bleed brakes. Thank you 👍 although I hear there is still separate fluid in the abs system that you can't access without opening some valve or something??

Have you got a segment home replacing the signal switch module on a 89 Corvette

you have a wealth of knowledge about the c4 corvette. I'm just learning. Greetings from Poland

you have a wealth of knowledge about the c4 corvette. I'm just learning. Greetings from Poland

next time don't shoot video after poppin ludes. Got the heavy eyelids and slow speech boy.

The all new cock pit interior for 1990 was literally a million times better,,,i never like 84 to 89 interiors was so cheep looking & digital dash you cant see in daylight.

From your first video I got an impression that brake hoses and brake master cylinder went totally empty. Service manual asks not to Do it. I followed your video instructions. I am wondering now, should I bleed the master cylinder first and after that each brake individually ?

I NEED THOSE JACKS! Where did you buy them?

Great info. I cleaned mine for the 1st time today (6/24). My 2003 C5 is a total garage queen so 2 out of 3 udders on the driver's side were clean. The 3rd udder had a few leaves in it. It is the same size as the other 2. It was a little tricky to get it re-installed. I haven't done the passenger side yet. 8-(

with the correction factors removed this car only makes 441/390 youre welcome

Need this to prevent power steering from leaking into my alternator lol

Slick trick, thank you!

chris how much you gas you put in your baby $4.00 dollars😅

chris put a little more lean to the right you in your vette baby when you drive😄

On my 1986 (w/Z51 suspension), there are a lot of differences. The rear shocks only have 2 18mm bolts. One on the bottom and one and on the top. And you only have to remove the one 18mm on the bottom and then slide it free. On the front, there is no panel to remove to get at the 5mm socket on top of the shock. I'm simply making a 1.5" hole in the top of the panel so I have access to the top of the shock. I'll use a rubber grommet to fill the hole when I am done.

I'm trying to look up the Corvette from the 80s that had a bit engine it's a concept car they keep showing this Corvette that looks like a jaguar

Is there a way to clean the top intake aluminum Chris?

More Like $73

What happens with the mileage on the old cluster, since it’s analog? Do you have to transfer it over to the new one? Is the new one dialed into what your mileage was?

Ive done mines last week. Time consuming, but rewarding in the end when done! Way better than hearing what it cost to be replaced at a local shop!

What is that panel in between the transmission panel and the oil pane of the engine?

Did you upgrade the knuckles? During the test / design phase of the C6 ZR1, GM engineers discovered notable flexing in the knuckle, which prompted them to manufacture a "beefier" knuckle and that was the upgraded knuckle from 2009 forward. It is a different part#. There's two corvette forum message strings with all the details and pictures.

Have you had any dash issues?

What kind of floor jack/lift is that? Thanks

30 min or less??? That's a 4 beer job Sir!!!!! At least half a day for customers..... If you run into rust and have to spray or etc.... C'mon man?

Chris, do know what size cam would be good for a C4 and a rough guess what it would cost 😉

Have you changed over to a 160 degree thermostat? I live in Florida and am contemplating changing over. Great film too!